English
FrançaisRegulations
Page 134 of 140, showing 20 records out of 2786 total, starting on record 2661, ending on 2680
| Title | Description | Implementation date | Source | Publication | Created |
|---|---|---|---|---|---|
| US ISO 2398:2006, Rubber hoses, textile-reinforced, for compressed air — Specification | This Uganda Standard specifies the requirements for three types, three classes and two categories of textile-reinforced rubber hose for compressed air, up to a maximum working pressure of 25 bar with an operating-temperature range of – 40 °C to + 70 °C, depending on the type and category | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 17 September 2016 |
| US ISO 2929:2014, Rubber hoses and hose assemblies for bulk fuel delivery by truck — Specification | This Uganda Standard specifies the requirements for two groups of rubber hoses and rubber hose assemblies for loading and discharge of liquid hydrocarbon fuels with a maximum working pressure of 10 bar (1,0 MPa). Both groups of hoses are designed for: • use with hydrocarbon fuels having an aromatic-hydrocarbon content not exceeding 50 % by volume and containing up to 15 % of oxygenated compounds; and • operation within the temperature range of − 30 °C to + 70 °C, undamaged by climatic conditions of − 50 °C to + 70 °C when stored in static conditions. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 17 September 2016 |
| US ISO 3861:2005, Rubber hoses for sand and grit blasting — Specification | This Uganda Standard specifies the requirements for rubber hoses for wet and dry sand and grit blasting, suitable for use up to a maximum working pressure of 6,3 bar and over an operating temperature range of −25 °C to +70 °C. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 17 September 2016 |
| US ISO 3862:2009, Rubber hoses and hose assemblies — Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water based fluids — Specification | This Uganda Standard specifies requirements for five types of spiral-wire-reinforced hydraulic hose and hose assembly of nominal size from 6,3 to 51. They are suitable for use with water-based hydraulic fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from −40 °C to +60 °C and oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C for types 4SP and 4SH and −40 °C to +120 °C for types R12, R13 and R15. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 22 September 2016 |
| US ISO 3949:2009, Plastics hoses and hose assemblies — Textile-reinforced types for hydraulic applications — Specification | This Uganda Standard specifies requirements for three types of textile-reinforced thermoplastics hose and hose assembly of nominal size from 3,2 to 25. Each type is divided into two classes dependent on electrical conductivity requirements. They are suitable for use with water-based hydraulic fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from 0 °C to +60 °C and oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C. This standard does not include requirements for end fittings. It is limited to the performance of hoses and hose assemblies. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 22 September 2016 |
| US ISO 3994:2007, Plastics hoses — Helical-thermoplastic reinforced thermoplastics hoses for suction and discharge of aqueous materials — Specification | This Uganda Standard specifies the requirements for three types of helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of water, weak aqueous chemical solutions and abrasive solids and slurries, for use in the ambient temperature range from − 10 °C to + 55 °C. The three types of hose are for light-, medium- and heavy-duty applications. The types of hoses covered in this standard are not intended for use with flammable or combustible materials, nor with aromatic solvents | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 22 September 2016 |
| US ISO 4079:2009, Rubber hoses and hose assemblies — Textile-reinforced hydraulic types for oil-based or water-based fluids — Specification | This Uganda Standard specifies requirements for five types of textile-reinforced hydraulic hose and hose assembly of nominal size from 5 to 100. They are suitable for use with water-based hydraulic fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from −40 °C to +60 ºC or oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C. This standard does not include requirements for end fittings. It is limited to requirements for hoses and hose assemblies. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 22 September 2016 |
| US ISO 4081:2010, Rubber hoses and tubing for cooling systems for internal combustion engines — Specification | This Uganda Standard specifies the requirements for straight or pre-formed rubber hoses and tubing for use in pressurized or unpressurized cooling circuits containing 1,2-ethanediol-based coolants in internal combustion engines for vehicles with an unladen mass (as defined in ISO 1176) of 3,5 t or less. In addition, this specification may also be applied as a classification system to enable original equipment manufacturers (OEMs) to detail a “line call-out” of tests for specific applications where these are not covered by the main types specified. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 22 September 2016 |
| ISO 4641:2010, Rubber hoses and hose assemblies for water suction and discharge — Specification | This Uganda Standard specifies the minimum requirements for textile-reinforced, smooth-bore rubber water-suction and discharge hoses and hose assemblies. Three types of hoses and hose assemblies are specified according to their operating duty requirements, i.e. their ambient and water temperature ranges: ambient temperatures: −25 °C to +70 °C; andwater temperatures during operation: 0 °C to +70 °C. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 22 September 2016 |
| US ISO 4642-1:2009, Rubber and plastics hoses, non-collapsible, for fire-fighting service — Part 1: Semi-rigid hoses for fixed systems | This Uganda Standard specifies the requirements and test methods for semi-rigid reel hoses for fire-fighting purposes for use with fixed systems. The hoses are intended for use at a maximum working pressure of 1,2 MPa for hoses of 19 mm and 25 mm inside diameter and 0,7 MPa for hoses of 33 mm inside diameter. Hoses conforming to this part of US ISO 4642 are intended for applications where long intervals can occur between the occasions of use, for example on fixed fire hose reels in buildings and other construction works. This part of US ISO 4642 applies exclusively to hoses for fire-fighting purposes intended for use at ambient conditions in non-aggressive or non-corrosive atmospheres within the temperature range −20 °C to +60 °C. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 4642-2:2009, Rubber and plastics hoses, non-collapsible, for fire-fighting service — Part 2: Semi-rigid hoses (and hose assemblies) for pumps and vehicles | This Uganda Standard specifies the requirements and test methods for semi-rigid reel hoses for use on fire-fighting vehicles and trailer pumps. The hoses are intended for use at a maximum working pressure of 1,5 MPa for normal pressure hoses (category I) and 4,0 MPa for high pressure hoses (category II). The hoses are further subdivided into types and classes (see Clause 4). This part of US ISO 4642 applies to delivery hoses for fire-fighting purposes intended for use at a minimum ambient temperature of −20 °C. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 5359:2008, Low-pressure hose assemblies for use with medical gases | This Uganda Standard specifies requirements for low-pressure hose assemblies intended for use with the following medical gases: oxygen; nitrous oxide; medical air; helium; carbon dioxide; xenon; specified mixtures of the gases listed above; oxygen-enriched air; air for driving surgical tools; nitrogen for driving surgical tools; vacuum. It is intended in particular to ensure gas-specificity and to prevent cross-connection between systems conveying different gases. These hose assemblies are intended for use at maximum operating pressures of less than 1 400 kPa. This standard specifies the allocation of (NIST), (DISS), (SIS) connectors to medical gases and specifies the dimensions of non-interchangeable screw-threaded (NIST) connectors. This standard does not specify:requirements for coaxial hoses used for the supply and disposal of air for driving surgical tools; andrequirements for electrical conductivity.This standard does not specify the intended uses of hose assemblies. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 5771:2008, Rubber hoses and hose assemblies for transferring anhydrous ammonia — Specification | This Uganda Standard specifies the minimum requirements for rubber hoses used for transferring ammonia, in liquid or in gaseous form, at ambient temperatures from −40 °C up to and including +55 °C. It does not include specifications for end fittings, but is limited to the performance of the hoses and hose assemblies. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 5772:1998, Rubber hoses and hose assemblies for measured fuel dispensing — Specification | This Uganda Standard specifies the requirements for three types of rubber hose and hose assembly used for measured fuel dispensing, including oxygenated fuels (up to a maximum of 15 % oxygenated compounds). The three types of hose are as follows:type 1: hoses with textile reinforcement suitable for reeling on a drum or hanging in bends;type 2: hoses with textile and helical wire reinforcement designed for torsional flexibility, suitable for coiling, reeling on a drum or hanging in bends; and type 3: hoses with fine wire reinforcement designed for low dilation, suitable for reeling on a drum or hanging in bends. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 5774:2006 Plastics hoses — Textile-reinforced types for compressed-air applications — Specification | This Uganda Standard specifies the requirements for four types of flexible thermoplastic hose, textile reinforced, for compressed-air applications in the temperature range from − 10 °C to + 60 °C. The four types are classified as light service for a maximum working pressure of 7 bar at 23 °C and 4,5 bar at 60 °C, medium service for a maximum working pressure of 10 bar at 23 °C and 6,5 bar at 60 °C, heavy service for a maximum working pressure of 16 bar at 23 °C and 11 bar at 60 °C, and heavy service for use in mining for a maximum working pressure of 25 bar at 23 °C and 13 bar at 60 °C | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 6134:2005, Rubber hoses and hose assemblies for saturated steam — Specification | This Uganda Standard specifies requirements for two types of hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high pressure with a maximum working pressure of 18 bar, made of rubber and hose fittings made of metal, designed to convey saturated steam and hot water condensate. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 6224:2011 Thermoplastics hoses, textile-reinforced, for general-purpose water applications — Specification | This Uganda Standard specifies the requirements for general-purpose textile reinforced thermoplastics water-discharge hoses. Three types of hose are specified according to their operating duty requirements, i.e. their ambient and water temperature ranges:ambient temperatures: −10 °C to +60 °C; and water temperature during operation: 0 °C to +60 °C. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 6804:2009, Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers — Specification | This Uganda Standard specifies the requirements for three types of rubber or plastics inlet hoses and hose assemblies for washing-machines and dishwashers connected to the domestic water supply at a pressure not exceeding 1 MPa (10 bar).It is applicable to the following types of hose: Type 1: rubber hoses for unheated water supply (maximum temperature 70 °C).Type 2: rubber hoses for heated water supply (maximum temperature 90 °C).Type 3: plastics hoses for unheated water supply (maximum temperature 60 °C). | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 6807:2003, Rubber hoses and hose assemblies for rotary drilling and vibration applications — Specification | This Uganda Standard specifies the requirements for textile- and steel-reinforced rubber hoses and hose assemblies for use with water-based and/or oil-based muds, up to a maximum temperature of 82 °C, which are pumped at high pressure in large volumes in rotary drilling service and which, when tested in accordance with ISO 2977, have a minimum aniline point of 66 °C. This standard applies to hoses which are suitable for use at ambient temperatures between − 20 °C and + 52 °C, unless changed by a supplementary requirement on request of the purchaser, and are resistant to ageing and tropical conditions. This standard does not apply to hoses which are intended for use with gases.. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 8028:1999, Rubber and/or plastics hoses and hose assemblies for airless paint spraying — Specification | This Uganda Standard specifies the requirements for four types, differentiated by burst pressure and temperature of use, of elastomeric hose and hose assembly for use in airless paint spraying. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
