English
FrançaisRegulations
Page 4 of 140, showing 20 records out of 2786 total, starting on record 61, ending on 80
| Title | Description | Implementation date | Source | Publication | Created |
|---|---|---|---|---|---|
| US ISO 2398:2006, Rubber hoses, textile-reinforced, for compressed air — Specification | This Uganda Standard specifies the requirements for three types, three classes and two categories of textile-reinforced rubber hose for compressed air, up to a maximum working pressure of 25 bar with an operating-temperature range of – 40 °C to + 70 °C, depending on the type and category | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 17 September 2016 |
| US ISO 6804:2009, Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers — Specification | This Uganda Standard specifies the requirements for three types of rubber or plastics inlet hoses and hose assemblies for washing-machines and dishwashers connected to the domestic water supply at a pressure not exceeding 1 MPa (10 bar).It is applicable to the following types of hose: Type 1: rubber hoses for unheated water supply (maximum temperature 70 °C).Type 2: rubber hoses for heated water supply (maximum temperature 90 °C).Type 3: plastics hoses for unheated water supply (maximum temperature 60 °C). | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 5772:1998, Rubber hoses and hose assemblies for measured fuel dispensing — Specification | This Uganda Standard specifies the requirements for three types of rubber hose and hose assembly used for measured fuel dispensing, including oxygenated fuels (up to a maximum of 15 % oxygenated compounds). The three types of hose are as follows:type 1: hoses with textile reinforcement suitable for reeling on a drum or hanging in bends;type 2: hoses with textile and helical wire reinforcement designed for torsional flexibility, suitable for coiling, reeling on a drum or hanging in bends; and type 3: hoses with fine wire reinforcement designed for low dilation, suitable for reeling on a drum or hanging in bends. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 3994:2007, Plastics hoses — Helical-thermoplastic reinforced thermoplastics hoses for suction and discharge of aqueous materials — Specification | This Uganda Standard specifies the requirements for three types of helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of water, weak aqueous chemical solutions and abrasive solids and slurries, for use in the ambient temperature range from − 10 °C to + 55 °C. The three types of hose are for light-, medium- and heavy-duty applications. The types of hoses covered in this standard are not intended for use with flammable or combustible materials, nor with aromatic solvents | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 22 September 2016 |
| US ISO 1403:2005, Rubber hoses, textile-reinforced, for general-purpose water applications — Specification | This Uganda Standard specifies the requirements for three types of general-purpose textile-reinforced rubber water hose with an operating temperature range of −25 °C to +70 °C and a maximum working pressure of up to 25 bar.These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine inlets, as firefighting hoses, for special agricultural machines or as collapsible water hoses. These hoses may be used with additives which lower the freezing point of water | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 17 September 2016 |
| US ISO 15465:2004, Pipework — Stripwound metal hoses and hose assemblies | This Uganda Standard specifies the requirements for the design, manufacture and testing of four principal types of stripwound metal hose and hose assemblies, of which only one type is for pressure applications. The four are: single overlap, unpacked and packed; double overlap, unpacked and packed, the last of these having maximum allowable pressures of up to 40 bar. These hoses and hose assemblies may be supplied in nominal sizes from DN 6 to DN 500 and may operate at temperatures up to 600 °C dependent on materials of construction | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 7989-2:2007, Steel wire and wire products — Nonferrous metallic coatings on steel wire — Part 2: Zinc or zinc-alloy coating | This Uganda Standard specifies the requirements for the coating mass per unit area, for other properties and also for testing of zinc or zinc-alloy coatings on steel wire and steel wire products, of circular or other section. | 2014-01-27 | The Uganda National Bureau of standards | THE UGANDA GAZETTE Vol. CVII No. 5 of JANUARY 2014 | 02 November 2016 |
| US ISO 7989-2:2007, Steel wire and wire products — Nonferrous metallic coatings on steel wire — Part 2: Zinc or zinc-alloy coating | This Uganda Standard specifies the requirements for the coating mass per unit area, for other properties and also for testing of zinc or zinc-alloy coatings on steel wire and steel wire products, of circular or other section. | 2014-01-27 | The Uganda National Bureau of standards | THE UGANDA GAZETTE Vol. CVII No. 5 of JANUARY 2014 | 12 April 2017 |
| US ISO 6807:2003, Rubber hoses and hose assemblies for rotary drilling and vibration applications — Specification | This Uganda Standard specifies the requirements for textile- and steel-reinforced rubber hoses and hose assemblies for use with water-based and/or oil-based muds, up to a maximum temperature of 82 °C, which are pumped at high pressure in large volumes in rotary drilling service and which, when tested in accordance with ISO 2977, have a minimum aniline point of 66 °C. This standard applies to hoses which are suitable for use at ambient temperatures between − 20 °C and + 52 °C, unless changed by a supplementary requirement on request of the purchaser, and are resistant to ageing and tropical conditions. This standard does not apply to hoses which are intended for use with gases.. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 4081:2010, Rubber hoses and tubing for cooling systems for internal combustion engines — Specification | This Uganda Standard specifies the requirements for straight or pre-formed rubber hoses and tubing for use in pressurized or unpressurized cooling circuits containing 1,2-ethanediol-based coolants in internal combustion engines for vehicles with an unladen mass (as defined in ISO 1176) of 3,5 t or less. In addition, this specification may also be applied as a classification system to enable original equipment manufacturers (OEMs) to detail a “line call-out” of tests for specific applications where these are not covered by the main types specified. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 22 September 2016 |
| US EAS 196:2013, High-strength low-alloy Carbon Steel for hot rolled sheet and cold rolled sheet — Specification | This Uganda Standard specifies the requirements for steel sheet in coils and cut lengths. It applies to the carbon steel and high-strength, low-alloy steel (HSLA) supplied as hot-rolled sheet and cold-rolled sheet. This standard is not applicable to hot-rolled, heavy-thickness carbon sheet coils. In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of the general specification. For the purposes of determining conformance with this specification and the various material specifications, values shall be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting values. | 2014-01-27 | The Uganda National Bureau of standards | THE UGANDA GAZETTE Vol. CVII No. 5 of JANUARY 2014 | 02 November 2016 |
| US EAS 196:2013, High-strength low-alloy Carbon Steel for hot rolled sheet and cold rolled sheet — Specification | This Uganda Standard specifies the requirements for steel sheet in coils and cut lengths. It applies to the carbon steel and high-strength, low-alloy steel (HSLA) supplied as hot-rolled sheet and cold-rolled sheet. This standard is not applicable to hot-rolled, heavy-thickness carbon sheet coils. In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of the general specification. For the purposes of determining conformance with this specification and the various material specifications, values shall be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting values. | 2014-01-27 | The Uganda National Bureau of standards | THE UGANDA GAZETTE Vol. CVII No. 5 of JANUARY 2014 | 12 April 2017 |
| US 1039:2013, Speedometers, mechanical odometers and chronotachographs for motor vehicles — Metrological requirements | This Uganda Standard specifies the requirements for speedometers, mechanical odometers and chronotachographs for motor vehicles. | 2013-10-25 | The Uganda National Bureau of standards | Uganda Gazette Vol. CV No. 54 of 25th October 2013 | 03 May 2017 |
| US ISO 8066-2:2001, Rubber and plastics hoses and hose assemblies for automotive air conditioning — Specification — Part 2: Refrigerant 134a | This Uganda Standard specifies the requirements for rubber or thermoplastic hoses and hose assemblies used for circulating liquid and gaseous R134a (tetrafluoroethane) in the air-conditioning systems of automobiles. The hoses and hose assemblies are designed in such a way as to restrict losses of refrigerant and contamination of the system. The operational temperature range is 40 °C to +125 °C | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 3861:2005, Rubber hoses for sand and grit blasting — Specification | This Uganda Standard specifies the requirements for rubber hoses for wet and dry sand and grit blasting, suitable for use up to a maximum working pressure of 6,3 bar and over an operating temperature range of −25 °C to +70 °C. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 17 September 2016 |
| US ISO 21809-5:2010, Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 5: External concrete coatings | This Uganda Standard specifies the requirements for qualification, application, testing and handling of materials required for the application of reinforced concrete coating externally to either bare pipe or pre-coated pipe for use in pipeline transportation systems for the petroleum and natural gas industries as defined in US ISO 13623. The external application of concrete is primarily used for the negative buoyancy of pipes used in buried or submerged pipeline systems and/or for the mechanical protection of the pipe and its pre-coating. This part of US ISO 21809 is applicable to concrete thicknesses of 25 mm or greater. | 2015-12-15 | The Uganda National Bureau of standards | The Uganda Gazette 22 January 2016: General Notice No. 45 of 2016 | 18 August 2016 |
| US ISO 21809-2:2014, Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 2: Single layer fusion-bonded epoxy coatings | This Uganda Standard specifies the requirements for qualification, application, testing and handling of materials for plant application of single layer fusion-bonded epoxy (FBE) coatings applied externally for the corrosion protection of bare steel pipe for use in pipeline transportation systems for the petroleum and natural gas industries as defined in US ISO 13623. | 2015-12-15 | The Uganda National Bureau of standards | The Uganda Gazette 22 January 2016: General Notice No. 45 of 2016 | 18 August 2016 |
| US ISO 21809-4:2009, Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 4: Polyethylene coatings (2-layer PE) | This Uganda Standard specifies the requirements for qualification, application, inspection, testing, handling and storage of materials for plant application of two-layer polyethylene coatings (2-layer PE) applied externally for the corrosion protection of bare steel pipe for use in pipeline transportation systems for the petroleum and natural gas industries as defined in US ISO 13623. | 2015-12-15 | The Uganda National Bureau of standards | The Uganda Gazette 22 January 2016: General Notice No. 45 of 2016 | 18 August 2016 |
| US ISO 8217:2012, Petroleum products — Fuels (class F) — Specifications of marine fuels | This Uganda Standard specifies the requirements for petroleum fuels for use in marine diesel engines and boilers, prior to appropriate treatment before use. The specifications for fuels in this standard can also be applicable to fuels for stationary diesel engines of the same or similar make and type as those used for marine purposes. This standard specifies four categories of distillate fuel, one of which is for diesel engines for emergency purposes. It also specifies six categories of residual fuel. | 2015-08-07 | The Uganda National Bureau of standards | THE UGANDA GAZETTE Vol. CVIII No. 43 of 7 August 2015 | 25 August 2016 |
| US ISO 4261:2013, Petroleum products — Fuels (class F) — Specifications of gas turbine fuels for industrial and marine applications | This Uganda Standard specifies the requirements for petroleum fuels for gas turbines (see ISO 3977) used in public utility, industrial, and marine applications. It does not cover requirements for gas turbine fuels for aviation use. This standard is intended for the guidance of users such as turbine manufacturers, suppliers, and purchasers of gas turbine fuels. This standard sets out the properties of fuels at the time and place of transfer of custody to the user. | 2015-08-07 | The Uganda National Bureau of standards | THE UGANDA GAZETTE Vol. CVIII No. 43 of 7 August 2015 | 25 August 2016 |
